Through this article, we will introduce to readers the definition, function and composition of high voltage BMS; the classification of system architecture, the working principle of high voltage BMS and the analysis of its various functions.
The BMS in the high voltage battery system collects data such as the voltage value of each battery cell, the temperature value of each temperature sensor, the total voltage value and total current value of the battery system, and the insulation resistance value of the battery system in real time, and collects data according to the settings set in the BMS.
The threshold determines whether the battery system is working normally and monitors faults in real time. The high-voltage battery system uses CAN to communicate with the VCU or charger through the BMS, and performs comprehensive management of charging and discharging of the high-voltage battery system.
The high-voltage battery system also receives and stores high-voltage DC power provided by on-board chargers, generators, brake energy recovery devices and external charging devices, and provides high-voltage components such as drive motor controllers, DC/DC, electric air conditioners, and PTCs. DC.
The high-voltage battery system mainly consists of four parts: high-voltage battery module, battery management system, high-voltage battery box and auxiliary components
1.Definition of high voltage BMS
New energy vehicle power batteries are composed of several single cells.
In mass production, there will inevitably be differences in the operating voltage, storage capacity, output power and temperature of single cells.
In actual use, the inconsistency between single cells will become more and more obvious due to factors such as regional environment, old age, overcharging, over-discharging, and high-temperature cycles, which will gradually lead to low battery efficiency and long service life. become shorter, and may even cause safety hazards such as explosion and burning.
Compared with battery life anxiety, the safety anxiety of pure electric vehicles is a topic that users are more concerned about. Data shows that 80% of spontaneous combustion accidents of new energy vehicles occur during charging or within 1 hour after being fully charged.
For power batteries, the performance of the battery pack is closely related to the performance of the single battery. If the single battery has the problems mentioned above, based on the “barrel principle”, the single battery with the worst charge and discharge status in the battery series circuit will have an impact on the charge and discharge of the entire battery pack, and then affect the entire power battery pack. efficiency and service life.
According to test data, the thermal management effect of new energy vehicles will affect more than 40% of the battery life.
In order to manage the hundreds or thousands of single batteries in the battery pack, effectively avoid fires caused by charging, and reduce safety accidents of electric vehicles, BMS came into being.
BMS consists of Battery Electronics and Battery Control Unit.
According to the definition of GB/T 19596, battery electronic components refer to electronic devices that collect electricity and heat-related data from battery cells (integrated) or battery modules (integrated) and provide these data to the battery control unit. .
Battery Control Unit refers to an electronic control component that controls or manages the electrical or thermal performance of the battery system and can interact with other control units on the vehicle.
BMS consists of Battery Electronics and Battery Control Unit.
According to the definition of GB/T 19596, battery electronic components refer to electronic devices that collect electricity and heat-related data from battery cells (integrated) or battery modules (integrated) and provide these data to the battery control unit. .
Battery Control Unit refers to an electronic control component that controls or manages the electrical or thermal performance of the battery system and can interact with other control units on the vehicle.
2.Main functions of high voltage BMS
BMS is an indispensable and important component of electric vehicles. It is the hub for managing and monitoring power batteries. It manages, maintains, and monitors each battery module. It is responsible for preventing battery overcharge and overdischarge, extending battery life, and helping batteries operate normally.
The battery management system (BMS) is an important link between vehicle batteries and electric vehicles. It handles a wide range of signals, including: battery cells, collision, CAN, battery charging systems, water pumps, high voltage, insulation, etc.
One over-discharge will cause permanent damage to the battery. In extreme cases, overheating or overcharging of the lithium battery can lead to thermal runaway, battery rupture or even explosion. Therefore, high voltage BMS must strictly control charging and discharging to avoid overcharging, over-discharging, and overheating.
The main functions of high voltage BMS like lithium ion bms include: real-time monitoring of battery physical parameters, battery status estimation, online diagnosis and early warning, charge and discharge and precharge control balance management, thermal management, etc. If any of the above functions is not implemented well, it will cause fatal harm to the battery.
3. Architectural classification of high voltage BMS
High voltage BMS architecture is generally divided into three categories: centralized, distributed, integrated/semi-distributed.
Centralized: All functions such as voltage, temperature acquisition, and power balancing are completed by the master control unit, and there is no slave control unit. There is no bus communication between the main control and the battery, and they are directly connected through the wiring harness.
The main control unit samples the voltage, current, temperature, etc. of the battery, then performs data processing, calculation and judgment, and finally issues control instructions.
The advantage of this design is that it has a simple structure, but the disadvantage is that it requires the use of relatively long and numerous wire harnesses, the overall reliability is not high, and when there are a large number of single cells, it will cause certain difficulties in calculation and management.
Distributed: The data collection of the distributed structure of high voltage BMS is decentralized, and the functions of the battery pack are relatively independent.
The entire system is divided into “single battery monitoring unit” and “battery management controller”.
The Cell Monitor Unit is installed on the single battery and is responsible for collecting and transmitting information from the single battery.
Several monitoring units are connected to the battery management controller BMU through signal lines for data communication, and then transmitted to the vehicle ECU through the CAN bus.
Compared with centralized BMS, distributed high voltage BMS reduces the use of wire harnesses, and the accuracy of monitoring data will be greatly improved. Moreover, since the monitoring unit and battery module are integrated, there is no limit on the overall number of battery packs.
Since the replacement of the power battery does not involve changes to the BMU, this BMS architecture is more conducive to models that adopt battery replacement mode.
Integrated/semi-distributed: Integrated/semi-distributed BMS is usually divided into main control module and measurement and control module, in which the measurement and control module can be divided into slave control module and high-voltage measurement and control module. Here are more about power grid ess.
The slave control module is generally installed on the lithium-ion battery pack to measure the voltage and temperature of individual cells and implement balancing control and thermal management control.
The high-voltage measurement and control module is generally installed in the central control box of the vehicle. It is mainly used to measure the total voltage, total current, energy, insulation resistance and control the high-voltage relay.
The main control module and the measurement and control module communicate with each other through the CAN bus.
As far as the entire system is concerned, the integrated/semi-distributed design uses fewer components, has a high degree of functional concentration, and has a simpler structure than the distributed one. It can improve the overall reliability and safety and is suitable for various types of battery pack designs. , including battery packs with unique module arrangements, which have a wider range of applications.
However, this kind of compromise design between distributed and centralized has a higher cost than the former two. Here are more about balcony solar storage system.







+86 – 18925002618




